Vapor linker exchange of partially amorphous metal–organic framework membranes for ultra-selective gas separation

Metal–organic framework (MOF) membranes are promising for efficient separation applications. However, the uncontrollable pathways at atomic level impede the further development of these membranes for molecular separation. Herein we show that vapor linker exchange can induce partial amorphization of MOF membranes and then reduce their transport pathways for precisely molecular sieving. Through exchanging MOF linkers by incoming ones with similar topology but higher acidity, the resulted metal-linker bonds with lower strength cause the transformation of MOF membranes from order to disorder/amorphous. The linker exchange and partial amorphization can narrow intrinsic apertures and conglutinate grain boundary/crack defects of membranes. Because of the formation of ultra-microporous amorphous phase, the MOF composite membrane shows competitive H₂/CO₂ selectivity up to 2400, which is about two orders of magnitude higher than that of conventional MOF membranes, accompanied by high H₂ permeance of 13.4 × 10⁻⁸ mol m⁻² s⁻¹ Pa⁻¹ and good reproducibility and stability.     

Tri-reformer with O2 side-stream distribution for syngas production

Methane tri-reforming combines steam reforming, dry reforming and partial oxidation of methane in a single reactor. The heat generated by the exothermic partial oxidation of methane can be used to supply the energy for the other two endothermic reactions (dry and steam reforming of methane). The thermoneutral condition allows the use of a tri-reformer with a simpler reactor structure since no external heat supply is necessary. Thermodynamic analysis of the thermoneutral reactor was performed using Gibbs free energy minimization approach. Conventional tri-reformers have heat and mass management problems. We developed a novel tri-reformer concept that utilizes proper distribution of O₂ gas to the reactor to address the problems. The optimization of the proposed reactor was performed with the objective function of minimizing total annual cost. Maintaining the peak temperatures by adjusting the O₂ flow rate at the distribution point along the reactor was shown to provide good load flexibility for the change in methane flow rate.     

内含实体对H型垂直轴风力机气动性能的影响

以H型垂直轴风力机及其内含圆柱形实体为研究对象,对NACA0018翼型的五叶片H型垂直轴风力机的气动性能进行数值模拟和实验验证。分析8种不同直径的内含圆柱体,在内含实体截面积占风轮迎风面积之比分别为21.2%、50.0%和76.9%时,风力机风能利用率的峰值分别下降8.04%、20.7%及74.3%。结果表明：随着内含实体直径的增大,风能利用率的峰值逐渐减小,开始较为缓慢,达到一定值时快速下降。小直径内含实体主要影响叶片在下风区的转矩,对风能利用率的影响较小,而大直径内含实体还会影响叶片在上风区的转矩,其风能利用率迅速减小。对于内含固定直径的实体,比如在现有建筑物外侧安装风力机时,其风轮半径的选择需综合考虑风能利用率和风力机的建造成本两方面的因素。研究结果可为建筑物与垂直轴风力机进行有效结合以提高风能的利用提供参考。     

Powder sintering and gel casting methods in making glass foam using waste glass: A review on parameters,performance, and challenges

The application of insulation materials in buildings and energy storage facilities is gaining global attention to reduce energy consumption, heat loss, and CO₂ emissions. Given the high insulation performance, glass foam is gaining popularity replacing combustible, high energy-consuming, and costly conventional insulation materials. The industrial process of glass foam manufacturing is an energy-consuming and non-ecofriendly process which requires the annealing of glass around its melting temperature. Therefore, researchers have developed powder sintering and gel casting methods to sinter glass foam mix at a temperature slightly above its glass transition point. However, research findings on these two methods are scattered because of the different parameters being used by researchers. The properties and performances of glass foam depend on the processing parameters, especially on the materials design and sintering conditions. Therefore, this study aimed to provide a comprehensive review on the key parameters for material selection and sintering of glass foams and provide necessary guidelines for the best practice and a direction for future research. Moreover, this review covers the current strategies and challenges associated with the powder sintering and gel casting methods including their sustainability and environmental performance.     

基于自适应LS-SVM的柴油机废气再循环冷却控制系统设计

针对当前柴油机废气再循环冷却控制系统受到时滞问题影响,导致系统开度走势与设定走势不一致、废气再循环效果差的问题,提出基于自适应LS-SVM的柴油机废气再循环冷却控制系统;以AT89C51单片机40针作为电控单元核心部件,利用位置传感器向系统发送负载信号,利用温度传感器来传输信号并反馈至D/A转换器;在D/A转换器中,反馈信号以串行或并行方式进入寄存器,并在转换后输出电流电压,控制系统阀门在排气再循环时的开启;伺服泵采用冷却系统,为系统提供液压动力源;利用自适应LS-SVM原理计算柴油机废气再循环冷却控制目标边界值,在最小二乘支持向量机基础上,利用求解线性方程组进行优化,消除了控制误差;根据控制差的大小,调整控制系统的输出值;由试验结果可知,该系统开度走势与设定开度走势一致,且与设定开度误差为1开度,说明使用该系统具有良好稳态特性,有效克服了系统中时滞问题,废气再循环效果较好。     

复杂环境下氧化铝储槽定向爆破拆除

在较为复杂的环境下,爆破拆除钢筋混凝土氧化铝储槽。该储槽自重大、呈圆形,内有4根立柱支撑下料漏斗。为使储槽顺利定向倒塌,通过爆破方案选择、参数确定,采取梯形切口和预处理以及安全防护和减振措施,使储槽爆破拆除获圆满成功。     

三维石墨烯-碳纳米管/水泥净浆的压敏性能

为了探索三维石墨烯-碳纳米管(G-CNTs)/水泥净浆的压敏性能,采用四电极法研究了荷载作用下GCNTs/水泥净浆的电阻率变化,并分析不同G-CNTs掺量、加载幅度、加载速度以及恒定荷载对电阻率变化的影响。研究表明:随着G-CNTs掺量的增加,电阻率呈先减小后稳定的变化趋势,在G-CNTs掺量由0.2wt%增加至1.6wt%时,电阻率下降51.8%;电阻率与温度呈负相关;G-CNTs掺量高于0.8wt%时可以显著提高水泥净浆的压敏性能,且电阻率变化率与应力应变有明显的对应关系,1.2wt%G-CNTs掺量下试件的应力灵敏系数和应变灵敏系数分别为2.3%/MPa和291;G-CNTs/水泥净浆电阻率变化率幅值随着加载幅度增大而相应增加,其电阻率变化率曲线在不同加载速度以及恒定荷载作用下均与应力-应变曲线一一对应,具有良好的压敏特性。     

Investigation of the Ga-Sb-S chalcogenide glass with low thermo-optic coefficient as an acousto-optic material

In this study, two series of Ga_xSb_40-xS₆₀ (x = 4, 6, 8, 10 mol%) and Ga_ySb₃₆S_64-y (y = 3, 5, 6 mol%) glasses were prepared and the relationship between their compositional and acousto-optic (AO) properties was investigated systematically for the first time. In the Ga_ySb₃₆S_64-y system, the AO figure of merit (M₂) increased as the Ga increased, and the maximum M₂ of the Ga₆Sb₃₆S₅₈ glass was 455.78 × 10^?18 s³/g, which is ～301 times greater than that of fused silica and ～2.5 times greater than that of As₂S₃ chalcogenide (ChG) glass at 1550 nm. However, its thermo-optic coefficients (dn/dT) varied greatly (32.1 × 10^?6 °C^?1–57.2 × 10^?6 °C^?1), and acoustic attenuations (α) at 10 MHz were high, from 5.446 dB/cm to 7.274 dB/cm. In the Ga_xSb_40-xS₆₀ glass system, the M₂ value and α at different ultrasonic frequencies gradually decreased with the improvement of Ga. Compared with the Ga_ySb₃₆S_64-y system, the Ga_xSb_40-xS₆₀ glass system had lower α (at 10 MHz) and dn/dT, which are 5.001 dB/cm–5.563 dB/cm and 17.3 × 10^?6 °C^?1–55.6 × 10^?6 °C^?1, respectively. These results provide a significant reference for the further development of novel ChG glasses and help expand their application fields.